Clik here to view.
After wire-wheeling all the bolts and chasing the threads in the trans. I...
After wire-wheeling all the bolts and chasing the threads in the trans. I reinstalled the pan.
View ArticleClik here to view.
This is the sump filter. It need's replacement as well.
This is the sump filter. It need's replacement as well.
View ArticleClik here to view.
The new filter installed. You just push the new filter up into the new seal...
The new filter installed. You just push the new filter up into the new seal and use the T-25 Torx bolt to secure it in place.
View ArticleClik here to view.
I have a seal seating tool but no dies small enough for this seal. I just...
I have a seal seating tool but no dies small enough for this seal. I just used the handle to drive the new seal in place. Be careful, you can easily distort the new seal and or mar up the aluminum...
View ArticleClik here to view.
Clik here to view.
Threaded the mounting bolts into the new gasket.
Threaded the mounting bolts into the new gasket.
View ArticleClik here to view.
After cleaning the pan of old fluid and gasket material, don't forget to...
After cleaning the pan of old fluid and gasket material, don't forget to reinstall the debris magnet.
View ArticleClik here to view.
This is the seal the instructions warn you about.
This is the seal the instructions warn you about.
View ArticleClik here to view.
Warning that comes with the replacement filter.
Warning that comes with the replacement filter.
View ArticleClik here to view.
I tried to remove the old filter seal with a pick, but it's a press fit. I...
I tried to remove the old filter seal with a pick, but it's a press fit. I ended up using a flat head screwdriver and hammer to drive the lip of the seal towards the center of the seal.Then I could...
View ArticleClik here to view.
You'll need a T-25 Torx driver to remove the filter's mounting bolt.
You'll need a T-25 Torx driver to remove the filter's mounting bolt.
View ArticleClik here to view.
What you'll see when the pan is dropped.The old filter and vlave body.
What you'll see when the pan is dropped.The old filter and vlave body.
View ArticleClik here to view.
I left 2 bolts in, one in the front and one in the rear of the pan. Took the...
I left 2 bolts in, one in the front and one in the rear of the pan. Took the dead blow hammer out and gave the pan a few taps until the pan seal was broken.Then using the two remaining bolts as pivot...
View ArticleClik here to view.
There are Fifteen 8mm bolts to remove to get the pan off.
There are Fifteen 8mm bolts to remove to get the pan off.
View ArticleClik here to view.
Purchsed the replacement filter and gasket kit for $ at my local Autoparts...
Purchsed the replacement filter and gasket kit for $ at my local Autoparts store.
View ArticleClik here to view.
After wire-wheeling all the bolts and chasing the threads in the trans. I...
After wire-wheeling all the bolts and chasing the threads in the trans. I reinstalled the pan.
View ArticleClik here to view.
The new filter installed. You just push the new filter up into the new seal...
The new filter installed. You just push the new filter up into the new seal and use the T-25 Torx bolt to secure it in place.
View ArticleClik here to view.
I have a seal seating tool but no dies small enough for this seal. I just...
I have a seal seating tool but no dies small enough for this seal. I just used the handle to drive the new seal in place. Be careful, you can easily distort the new seal and or mar up the aluminum...
View ArticleClik here to view.
Clik here to view.
Threaded the mounting bolts into the new gasket.
Threaded the mounting bolts into the new gasket.
View Article
